навигация
Новости
Обновлена программа управления МДМ-500М October 23, 2018
ПО IT100Sync для работы с анализатором ИТ-100 October 3, 2018
Приглашаем посетить наш стенд на выставке РАДИОЭЛЕКТРОНИКА И ПРИБОРОСТРОЕНИЕ September 7, 2018
Размещены видеоролики по работе с анализатором ИТ-100 August 6, 2018
Продление действия Свидетельства об утверждении типа для ОБЗОР-304 July 24, 2018
Новые возможности головной станции BTA10 July 4, 2018
Получено Свидетельство об утверждении типа средств измерений на векторные рефлектометры CABAN R60, CABAN R180 June 9, 2018
Приглашаем посетить наш стенд на выставке ANGA COM 2018 May 28, 2018
Добавлена функция удаленного управления анализатором ТВ сигналов мультисистемным ИТ-100 May 28, 2018
Обновлено программное обеспечение МДМ-500М May 23, 2018
 
Вы здесь: Главная Products Measurement Instruments TV Meters IT-100 Multisystem TV Signal Analyzer
Действия с Документом

IT-100 Multisystem TV Signal Analyzer

IT-100 Multisystem TV Signal Analyzer
IT-100 TV signals multisystem analyzer is designed to measure signals parameters of digital and analog television. The analyzer can be used when checking and servicing cable coaxial, fiber-optic or IP networks for receiving television and radio broadcasting, separate elements of network building and other radio electronic devices.

Measuring TV signals parameters:

  • Analog television: support for PAL, SECAM, NTSC standards.

Measured parameters: Level, Video/Audio, Carrier/Noise (inband and outband of video signal), modulation depth, unwanted modulation level (HUM), CSO&CTB distortion components level.

  • Cable digital television: support for DVB-C, ITU-T J.83 Annex B, C standards.

Measured parameters: power, MER, BER, constellation diagram, error analysis over time.

  • Terrestrial digital TV broadcasting: support for DVB-T, DVB-T2 standards.

Measured parameters: power, MER, BER, constellation diagram, echo diagram, error analysis over time.

  • Satellite broadcasting digital television: support for DVB-S, DVB-S2 standards.

Measured parameters: power, MER, BER, constellation diagram, error analysis over time.

  • IP digital television: support for UDP and RTP protocol, reception of the Transport Stream through unicast and multicast (IGMPv2).

Measured parameters: average bitrate, number of lost packets (for RTP), jitter of packets arrival interval.

Additional features of the IT-100 analyzer:

  • Monitoring of TV picture and audio:
    • Monitoring of PAL, SECAM, NTSC analog channels
    • Monitoring of radio FM stations
    • Monitoring of digital channels with MPEG-1, MPEG-2, MPEG-4, H.264 encoding with SD or HD resolution
    • Monitoring of encrypted programs when installing the CAM module
    • Monitoring of IPTV channels
  • MPEG Transport Stream analysis:
    • Three-level analysis for compliance with the TR101290 requirements
    • Real-time analysis
    • Recording a transport stream to a file for further analysis
  • Support of measurements in fiber optic cable network:
    • Built-in optical receiver with a frequency range up to 2150MHz
    • Support of all measurements from the optical input
    • Measurement of optical signal power
    • Operating in the wavelength range from 1100 to 1650 nm
    • Replaceable FC and SC adapters of the input optical connector
  • Power supply of external devices:
    • Built-in remote feeding power supply from 5 to 24V
    • Support for DiSEqC protocol level 2.1
    • 5W power of remote feeding power supply
    • Measurement of DC and AC voltage on the input RF connector
  • Interface Support:
    • USB 2.0 device for connecting the analyzer to a personal computer
    • USB 2.0 host for connecting FLASH drives
    • ETHERNET RJ45 10 / 100M for software updates, remote control and IPTV operation
    • PCMCIA port for connecting a CAM module
  • General specifications:
    • Operating frequency range: 5 to 2150MHz
    • Level measurement range: 20 to 120 dBμV
    • Level measurement accuracy: ± 1.2dB
    • Frequency step: 25 kHz
    • Sweep time in the spectrum mode from 70 to 250 msec
    • Built-in TFT color display 4.3 "with a resolution of 480x272 pixels
    • Built-in speaker
    • Operation from built-in battery and mains charger
    • Battery life: 4 hours
    • Analyzer weight: 1.5 kg
    • Operating temperature range: -10 to +500С

IT100Sync software introduces the following functions:

  • Create and edit channel plans, limit plans, satellites and LNB profiles
  • Copy, move and delete files on IT-100 and USB flash drive connected to PC
  • View measurement results in a convenient form
  • Synchronize data between PC and the Meter

Software for OS Linux is available on request.

 

Operating modes
Main Menu Mode
Full Scan in Limit Mode
Full Scan in Tilt Mode
Main Menu Mode
Full Scan in Limit Mode
Full Scan in Tilt Mode
Channel Mode for digital channels
Channel Mode for analog channels
Autotest Channel Mode
Channel Mode for digital channels
Channel Mode for analog channels
Autotest Channel Mode
Autotest Channel Mode
MPEG TS analysis Mode
MPEG TS analysis Mode
Autotest Channel Mode
MPEG TS analysis Mode
MPEG TS analysis Mode
TV picture Mode
Spectrum Analyzer Mode
Channel Mode for satellite channels
TV picture Mode
Spectrum Analyzer Mode
Channel Mode
for satellite channels

Персональные инструменты